
IAG Performance sells its Spec Street Series coilovers, built by Fortune Auto, as a separate kit for each Subaru WRX and STI chassis. On IAG’s own pages, every listing is limited to specific years, and several are marked WRX-only or STI-only. If you’re shopping for IAG Street Series coilovers, the part number is the first thing to get right. Here’s how the part numbers line up with each car, and what the listings say about the hardware.
Still deciding between coilovers and air suspension? Our sister site compares them in Air Suspension vs Coilovers: Which Wins?
IAG Street Series coilovers: one part number per chassis
| Car | IAG part number | In our store |
|---|---|---|
| 2002–2007 WRX and 2004 STI | IAG-SUS-1006 | Search our store for the part number |
| 2005–2007 STI | IAG-SUS-1002 | Search our store for the part number |
| 2008–2014 WRX (WRX only) | IAG-SUS-1007 | IAG-SUS-1007 for the 2008–2014 WRX |
| 2008–2014 STI (STI only) | IAG-SUS-1003 | IAG-SUS-1003 for the 2008–2014 STI |
| 2015–2021 WRX and STI | IAG-SUS-1004 | IAG-SUS-1004 for the 2015–2021 WRX and STI |
| 2022-and-newer WRX | IAG-SUS-1005 | IAG-SUS-1005 for the 2022+ WRX |
About IAG-SUS-1005: our product title for this kit reads “2002+ WRX,” but the description and fitment line on the same page, and Import Image Racing’s listing for IAG-SUS-1005, describe it as a 2022-and-newer WRX kit. Treat it as the 2022+ kit. The 2002–2007 cars use IAG-SUS-1006.
IAG’s pages also show the 2008–2014 WRX and STI on separate kits. Don’t assume the WRX kit fits an STI of the same year, or the reverse.
What the store listings say about the hardware
IAG’s own product pages for these kits don’t publish detailed specs, so the figures below come from our store listings and Import Image Racing’s listing. Confirm anything critical with IAG before ordering.
| Kit | Spring rate (front / rear) | Front stroke / body | Other listed hardware |
|---|---|---|---|
| IAG-SUS-1007 (2008–2014 WRX) | 7 / 8 kg/mm | 127mm / 270mm | Aluminum camber plates and spring perches; 1-inch extended top hats |
| IAG-SUS-1003 (2008–2014 STI) | 7 / 8 kg/mm | 127mm / 270mm | Aluminum camber plates and spring perches; 1-inch extended rear top hats; monotube, rebuildable |
| IAG-SUS-1004 (2015–2021 WRX/STI) | 7 / 8 kg/mm | 127mm / 270mm | Aluminum camber plates and spring perches; 1-inch extended top hats; monotube |
| IAG-SUS-1005 (2022+ WRX) | 7 / 7 kg/mm | 117mm / 240mm | 1-inch extended rear top hats; monotube |
The listings describe the damping adjuster differently. Import Image Racing’s listing for the 2022+ kit calls the coilovers “single adjustable,” and one store listing describes 24 rebound positions with no external compression adjustment. Two others say “24 clicks of rebound and compression adjustment.” Expect a single damping adjuster, and check the instructions that ship with your kit.
Before you bolt them in
- Confirm the chassis and year against the part number table. The 2008–2014 STI listing also warns to check fit if the car has aftermarket knuckles or other modified suspension parts.
- Set ride height with the right method. Our sister site’s article How to Install Coilovers Without Wrecking Your Ride explains how to measure and adjust height in small, even steps without changing spring preload. It also covers tightening bushing bolts at ride height rather than with the suspension hanging.
- Start camber plates near the middle of their range unless you know the alignment you want. Very negative camber on a street car wears the inside of the tires.
- Get an alignment. Two of the store listings for these kits call for one after installation, and the sister-site install article says to do it once the car has settled at its new height.
