
A 927-100 front sway bar kit is listed for a long run of front-wheel-drive GM cars and minivans: Chevy Impala and Monte Carlo, Buick Century and Regal, Pontiac Grand Prix and more. That broad coverage is handy, but it also means the fitment lists don’t always agree. This guide explains what 927-100 refers to, which vehicles the manufacturer listings agree on, where they conflict, and how the kits in our store differ.
If you’re new to sway bars, our sister site explains what a sway bar does and why the end links and bushings matter.
What is a 927-100 front sway bar?
927-100 is Dorman’s part number for a 33mm front sway bar kit. Many other brands now use it as a reference, so a listing titled “927-100” isn’t necessarily a Dorman part. The kit is meant to replace the factory front stabilizer bar, and Dorman lists a long set of GM original-equipment numbers it replaces. Dorman also cross-references MOOG K170001, a solid front sway bar kit that MOOG lists for many of the same vehicles.
Which vehicles do the 927-100 and K170001 listings agree on?
We compared Dorman’s 927-100 application list with MOOG’s product information sheet for K170001. Both list these vehicles for the same years:
| Make | Model | Years both sources list |
|---|---|---|
| Chevrolet | Impala | 2000–2013 |
| Chevrolet | Monte Carlo | 2000–2007 |
| Chevrolet | Venture | 1998–2005 |
| Buick | Century | 1997–2005 |
| Buick | Regal | 1997–2004 |
| Oldsmobile | Intrigue | 1998–2002 |
| Oldsmobile | Silhouette | 1997–2004 |
| Pontiac | Grand Prix | 1997–2003 |
| Pontiac | Montana | 2000–2005 |
| Pontiac | Trans Sport | 1997–1998 |
If your car is in this table, both manufacturers list it. You should still check the details below before ordering.
Where the fitment lists disagree
Some vehicles and years appear in one source but not the other. Treat these as “verify first,” not as confirmed fits:
- 2014–2016 Impala: Dorman lists the Impala Limited for these years. The Limited is the carry-over version of the older car, not the redesigned Impala sold alongside it. MOOG’s sheet lists the Impala through 2016 without separating the Limited. If you have a 2014–2016 Impala, confirm which version it is.
- Pontiac Grand Prix 2004–2008: Dorman lists 1997–2003 and 2006–2008. MOOG lists 1996–2005. Several store listings also note that some Grand Prix applications may use a 34mm bar rather than 33mm. Measure your original bar or confirm the OE number before ordering.
- Buick Rendezvous and Pontiac Aztek: listed by MOOG and by the aftermarket 927-100 kits, but not in the Dorman application list we reviewed.
- Early and late years: Dorman starts the Venture at 1997 and the Montana at 1999. MOOG starts them at 1998 and 2000.
When two sources disagree, the most reliable tiebreaker is the original part. Give your VIN to a GM parts counter, or measure and compare the bar that’s on the car now.
Comparing the 927-100 and K170001 kits in our store
All of the kits below are listed as 927-100 or K170001 replacements, but they don’t list the same contents. If you plan to replace the bushings and brackets at the same time, check what’s in the box.
| Kit | What the listing says is included | Notes |
|---|---|---|
| MOOG K170001 front sway bar kit | Solid front bar, MOOG Problem Solver end links, and bushings where applicable | MOOG’s sheet also lists new coated brackets and hardware. Bar diameter isn’t stated on the listing |
| LOBIUTIYA 927-100 kit with end links | 33mm bar, 2 bushings, 2 bushing brackets, 4 mounting screws, end link kit, installation hardware | Clear parts list |
| bansdans 927-100 kit | 33mm bar, 2 bushings, 2 bushing brackets, 4 mounting screws, end link kit | Clear parts list |
| A-Premium 927-100 kit | 33mm bar, 2 end links, 2 mounting brackets, hardware set | Bushings aren’t listed among the contents. Confirm before ordering if you need them |
| Dasbecan 927-100 front sway bar | Contents not itemized on the listing | Check the product page for what’s included |
Before you order: a four-point check
- Find your car in the table above. If it’s only in the “disagree” list, verify by VIN before you buy.
- Check the bar diameter. The 927-100 kits are listed as 33mm. Some Grand Prix applications are noted as 34mm.
- Decide what you’re replacing. If only the end links or bushings are worn and the bar is straight, a full bar kit may be more than you need.
- Confirm the contents. If you want new bushings and brackets, choose a kit that lists them.
Our sister site’s guide on choosing and installing sway bars makes the same point: match the bar to your exact year, model, trim and suspension package.
Installation notes
A front sway bar and its end links affect how the car handles. Follow the procedure and torque values in the factory service information, and use the supplied hardware or new hardware where required. For a general walkthrough, including clearance checks and listening for clunks after the job, see How to Upgrade Sway Bars for Better Handling. If you can’t support the car safely or aren’t comfortable working on suspension fasteners, have a qualified shop do the installation.
Frequently asked questions
Is 927-100 the same as MOOG K170001?
Dorman lists MOOG K170001 as an interchange for 927-100. They’re different brands’ kits for many of the same vehicles, and their published application lists don’t match exactly.
Does a 927-100 sway bar fit a 2014–2016 Chevy Impala?
Dorman lists the 2014–2016 Impala Limited, the carry-over version of the older Impala. Confirm which version you have before ordering.
What size is the 927-100 sway bar?
Dorman lists it as 33mm. Some store listings note that certain Pontiac Grand Prix applications may use a 34mm bar.
Does it fit a Buick Rendezvous or Pontiac Aztek?
MOOG lists those vehicles for K170001, and the aftermarket 927-100 kits list them too, but the Dorman application list we reviewed does not. Verify by VIN.
