Deep Bass Response from 8 Hz to 250 Hz
The Taramps BASS 400 is designed specifically for low-frequency audio reproduction.
Its 8 Hz–250 Hz frequency response covers the bass frequencies commonly handled by dedicated car subwoofers.
This makes it suitable for adding low-frequency depth to factory stereo systems that lack substantial bass output.
When paired with an appropriate subwoofer enclosure and correctly configured crossover settings, the amplifier can help create a fuller, more balanced listening experience.
The frequency-response specification does not mean every connected subwoofer will reproduce the entire range at equal output. Actual bass response depends heavily on the subwoofer, enclosure, and vehicle.
Adjustable Parametric Bass Boost for Custom Tuning
One of the standout features of the Taramps BASS 400 is its adjustable parametric bass boost.
The control allows you to select a boost frequency between 35 Hz and 55 Hz, with up to +12 dB of additional emphasis.
This provides more flexibility than a basic fixed-frequency bass boost control.
35 Hz Bass Emphasis
Lower boost frequencies can emphasize deeper bass content when the connected subwoofer and enclosure are capable of reproducing those frequencies safely.
45 Hz Bass Emphasis
A setting near the middle of the adjustment range may help emphasize bass impact in some systems.
55 Hz Bass Emphasis
Higher boost frequencies can emphasize upper-bass punch, depending on the subwoofer and enclosure response.
Important: A +12 dB boost represents a substantial increase in the requested amplifier output at the boosted frequency. Excessive boost can cause clipping, overheating, or subwoofer damage. Start with bass boost disabled and make gradual adjustments.
Ideal for Single 10-Inch and 12-Inch Subwoofer Systems
The Taramps BASS 400 is a practical choice for many modest-power aftermarket subwoofer installations.
It can be paired with compatible:
- Single 10-inch subwoofer enclosures
- Single 12-inch subwoofer enclosures
- Compact sealed subwoofer systems
- Properly matched ported subwoofer boxes
- Custom trunk-mounted bass systems
- Factory stereo subwoofer upgrades
The subwoofer’s nominal impedance and RMS power-handling rating matter more than its diameter when determining amplifier compatibility.
For a 2-ohm amplifier, verify that the final wiring configuration meets the manufacturer’s minimum supported impedance.
Upgrade Your Factory Stereo Without Replacing Everything
You don’t necessarily need to replace your entire factory audio system to enjoy better bass.
The Taramps BASS 400 can be integrated into many factory stereo systems with the appropriate signal-conversion equipment and wiring.
If your factory radio lacks RCA subwoofer outputs, a compatible line output converter or vehicle-specific audio interface may be required.
This allows the amplifier to receive an appropriate audio signal while continuing to use the original stereo.
Factory premium audio systems may require additional integration hardware, particularly when they use proprietary amplifiers, active crossovers, or digital audio connections.
DIY Stereo Wiring Diagrams and Installation Guides
Planning to install the Taramps BASS 400 in your car or truck? Identifying the correct factory stereo wiring is an important first step.
My Pro Street Online offers vehicle-specific stereo wiring references that can help when adding an aftermarket amplifier and subwoofer.
Honda Civic Stereo Wiring
Use the Honda Civic Stereo Wiring Diagram to help identify factory radio and speaker connections before installing an aftermarket subwoofer amplifier.
Nissan 240SX Stereo Upgrade
Building a custom S13 or S14 audio system? Consult the Nissan 240SX Stereo Wiring Diagram when planning an aftermarket head-unit and subwoofer installation.
Nissan Altima Speaker Wiring
Reference the Nissan Altima Stereo Wiring Diagram when identifying factory audio connections for a bass upgrade.
For more DIY automotive wiring and stereo installation resources, visit My Pro Street Online.
Pro Street Installation Tip: Factory stereo wiring diagrams help identify audio signals and control connections. Always supply amplifier power through appropriately sized, fused battery wiring rather than the factory stereo harness.
Aluminum Housing for Heat Dissipation
The Taramps BASS 400 features an aluminum housing designed to assist with heat dissipation.
Proper thermal management is important for car audio amplifiers, particularly when operating at higher output levels for extended periods.
For best results, mount the amplifier in a secure, ventilated location away from direct water exposure and excessive heat.
Avoid enclosing the amplifier in a tightly sealed compartment without adequate airflow.
Integrated Thermal and Short-Circuit Protection
The BASS 400 includes protection circuitry designed to respond to common electrical and thermal faults.
Thermal Protection
Helps protect the amplifier when internal temperatures exceed its intended operating range.
Short-Circuit Protection
Helps reduce the risk of amplifier damage caused by certain speaker wiring faults.
These features do not replace proper installation practices, suitable speaker impedance, correct grounding, or appropriately rated circuit protection.
Taramps BASS 400 Technical Specifications
| Specification | Details |
|---|---|
| Brand | Taramps |
| Series | BASS |
| Model | BASS 400 |
| Amplifier Type | Monoblock Subwoofer Amplifier |
| Rated RMS Power | 400W |
| Rated Impedance | 2 Ohms |
| Frequency Response | 8 Hz–250 Hz |
| Parametric Bass Boost | Adjustable |
| Bass Boost Frequency Range | 35–55 Hz |
| Maximum Bass Boost | +12 dB |
| Housing Material | Aluminum |
| Thermal Protection | Yes |
| Short-Circuit Protection | Yes |
| Intended Application | Dedicated Subwoofer Systems |
Installation Tips for the Taramps BASS 400
Before installing the amplifier, verify the impedance and RMS power-handling rating of your subwoofer.
Select an appropriately sized power cable and ground connection according to the manufacturer’s installation requirements.
Install a correctly rated fuse close to the battery to protect the amplifier power cable.
Mount the amplifier securely in a location with adequate ventilation.
Connect the amplifier to a compatible audio signal source, then connect the subwoofer using appropriately sized speaker wire.
Set amplifier gain correctly before adjusting the bass boost.
If the system uses a ported enclosure, follow the enclosure and subwoofer manufacturer’s recommendations for protecting the driver against excessive low-frequency excursion.
Do not operate the amplifier below its specified minimum speaker impedance.
Why Choose the Taramps BASS 400?
The Taramps BASS 400 provides a practical balance of continuous power, dedicated bass amplification, and adjustable low-frequency tuning.
Its 400W RMS rating makes it suitable for many everyday subwoofer upgrades, while its adjustable 35–55 Hz parametric bass boost allows drivers to tailor bass emphasis to their preferences.
For enthusiasts who want a dedicated subwoofer amplifier without moving into extremely high-power electrical system upgrades, the BASS 400 is a compelling option.
Add Better Bass with Pro Street Online
Upgrade your daily driving experience with the Taramps BASS 400 2 Ohm 400W RMS Monoblock Subwoofer Amplifier.
Pair it with a compatible subwoofer, quality amplifier wiring, and the appropriate stereo integration hardware to build a clean, reliable bass system.
Explore more aftermarket subwoofers, amplifiers, car stereos, and installation accessories at Pro Street Online.
There are no reviews yet.