Power Your Front and Rear Speakers
Use the four-channel configuration to amplify your vehicle’s front and rear speakers independently.
This makes the CBA2000.4 a practical choice for upgrading factory door speakers or installing aftermarket coaxial speakers.
Upgrade to Component Speakers
Planning to install separate tweeters and midrange drivers?
The CBA2000.4 can power compatible component speaker systems when used with the correct passive crossovers or external audio processing.
Build a Custom Aftermarket Stereo System
Combine the ORION amplifier with an aftermarket head unit, properly matched speakers, and quality wiring to create a more capable audio system.
The amplifier’s adjustable filters make it easier to tailor speaker output to your installation.
ORION CBA2000.4 RMS Power Ratings
| Speaker Impedance | Continuous Output |
|---|---|
| 4 Ohms | 40W RMS × 4 |
| 2 Ohms | 75W RMS × 4 |
| Advertised Maximum Power | 2000W |
These manufacturer-provided RMS figures are the most useful starting point when selecting compatible speakers.
For example, a set of aftermarket 4-ohm speakers rated for approximately 40–75 watts RMS may be a reasonable candidate, provided the amplifier is configured correctly and the speakers’ operating requirements are satisfied.
Installation Tip: The advertised 2000-watt rating is a maximum marketing figure, not the amplifier’s continuous RMS output.
Class A/B Amplifier Technology for Full-Range Sound
The ORION CBA2000.4 uses Class A/B amplifier architecture, a traditional design commonly used in automotive full-range audio systems.
Class A/B technology combines aspects of Class A and Class B operation to provide audio amplification with reduced crossover distortion compared with a basic Class B output stage.
For drivers who prefer a conventional analog amplifier design, the CBA2000.4 offers an accessible way to power upgraded car speakers.
Its MOSFET power supply supports the amplifier’s internal electrical requirements, while the chassis helps dissipate heat generated during operation.
Like other Class A/B amplifiers, the CBA2000.4 requires appropriate ventilation and correctly sized electrical wiring for dependable performance.
Adjustable Crossovers for Custom Sound Tuning
High-Pass Filter (HPF)
The adjustable high-pass filter helps prevent unnecessary low-frequency signals from reaching smaller door speakers.
This can reduce excessive speaker excursion and improve clarity when your audio system includes a dedicated subwoofer.
Low-Pass Filter (LPF)
The low-pass filter allows installers to limit higher frequencies in supported amplifier configurations.
This feature provides flexibility when integrating the amplifier into a custom audio system.
Bass Boost
The amplifier’s bass boost function allows additional low-frequency emphasis.
Use conservative settings to avoid clipping, distortion, and unnecessary speaker stress.
Compatible with Aftermarket Car Stereos and Head Units
The ORION CBA2000.4 features RCA low-level inputs designed for compatible aftermarket car stereos and audio processors.
If your head unit includes RCA preamp outputs, you can connect the amplifier using appropriate RCA signal cables.
For factory radios without RCA outputs, a compatible line output converter may be required.
Factory amplified audio systems may also require specialized integration hardware to retain factory functions and provide the correct signal level.
When upgrading a stereo, always verify the vehicle’s wiring diagram and factory amplifier configuration before making connections.
MOSFET Power Supply and Built-In Protection
The CBA2000.4 uses a MOSFET power supply to support its four-channel amplification circuitry.
Its two-way protection system is designed to respond to specified operating faults and help reduce the risk of amplifier damage.
For reliable performance, ensure the amplifier is installed with appropriate power and ground wiring, battery-side circuit protection, and adequate ventilation.
ORION CBA2000.4 Technical Specifications
| Specification | Details |
|---|---|
| Brand | ORION |
| Series | Cobalt |
| Model | CBA2000.4 |
| Amplifier Type | 4-Channel |
| Amplifier Class | Class A/B |
| Advertised Maximum Power | 2000W |
| RMS Output at 2 Ohms | 75W × 4 |
| RMS Output at 4 Ohms | 40W × 4 |
| Supported Speaker Loads | 2Ω / 4Ω |
| Frequency Response | 10 Hz–30 kHz |
| Power Supply | MOSFET |
| Signal Inputs | RCA Low-Level |
| High-Pass Filter | Yes |
| Low-Pass Filter | Yes |
| Bass Boost | Yes |
| Protection Circuitry | Two-Way Protection |
| Intended Application | Full-Range Car Speaker Amplification |
Installation Tips for the ORION CBA2000.4
Before installing your new amplifier, identify the factory speaker wiring and verify the impedance of each connected speaker.
Mount the amplifier securely in a ventilated location, and use appropriately sized power and ground wiring.
Install a properly rated fuse near the battery to protect the amplifier’s power cable.
Connect the RCA inputs to compatible head-unit preamp outputs, then connect the amplifier’s speaker channels to the appropriate speakers.
When first powering the system, begin with low gain settings and adjust the crossover controls to match your speakers.
For systems with a separate subwoofer amplifier, a high-pass filter setting around 80 Hz can be a useful starting point for many door speaker installations.
Why Choose the ORION CBA2000.4 Cobalt Amplifier?
The ORION CBA2000.4 combines four-channel amplification, traditional Class A/B design, and adjustable audio controls in a package intended for everyday stereo upgrades.
Its RMS output ratings make it suitable for many aftermarket speaker systems, while the RCA inputs provide straightforward connectivity with compatible aftermarket head units.
Whether you’re restoring a classic car, upgrading a Japanese performance vehicle, or improving the sound quality of your daily driver, the Cobalt Series offers a practical foundation for a custom audio installation.
Upgrade Your Stereo with Pro Street Online
Give your aftermarket speakers the dedicated amplification they deserve.
The ORION CBA2000.4 Cobalt 2000W 4-Channel Class A/B Amplifier offers adjustable sound tuning, four-channel output, and MOSFET power supply technology for a more capable automotive audio system.
Explore more aftermarket stereos, car audio amplifiers, speakers, and installation accessories at Pro Street Online.
There are no reviews yet.