GMT800 Front Drop: Spindles or Coils for 1999–2006 Silverado

The 1999–2006 Chevy Silverado 1500 and GMC Sierra 1500, the GMT800 trucks, are a common starting point for a lowered street truck. For a GMT800 front drop, there are two main bolt-in approaches: drop spindles, which move the wheel’s mounting point higher, or lower-height front coils. Each has its own fitment limits, and the listings for both are specific about which trucks they skip. Here’s how the options in our store compare and what to check on your truck first.

For how a front drop fits into a full lowered build, including the rear, wheels and bump stops, see our sister site’s A Street Truck Suspension Build Example Done Right.

GMT800 front drop: what spindles and coils each change

A drop spindle relocates the wheel’s mounting point on the steering knuckle. The truck sits lower, but the front springs and their rate stay the same. The sister-site build article puts it simply: a spindle lowers the truck at the wheel while preserving spring rate. A lowering coil replaces the factory front spring with a shorter one, so the spring itself sets the new ride height.

PartAdvertised front dropListed forWhat’s in the box
munirater 2-inch drop spindles2 inches (may vary by application)1999–2006 Silverado/Sierra 1500 2WD (see the 4WD note below)Left and right spindles; hubs, bearings and brakes not listed
TOWGUARD 2-inch front lowering coilsAbout 2 inches on Extended and Crew Cab; about 1 inch on Regular Cab1999–2006 Silverado/Sierra 1500 and 2007 Classic: 2WD, V8, non-HDTwo front coil springs
Gleyi 3-inch front lowering coilsAbout 3 inches (varies by cab, bed, engine and spring wear)1999–2006 Silverado/Sierra 1500 and 2007 Classic: 2WD, V8 (4.8L and 5.3L)Two front coil springs

Note the cab difference on the TOWGUARD coils. The same spring is listed at about 2 inches of drop on a heavier Extended or Crew Cab and about 1 inch on a Regular Cab.

Trucks the listings exclude

The two coil listings are specific about what they don’t cover:

  • 4WD and AWD trucks, which use torsion bars up front rather than coil springs.
  • V6 trucks (both coil listings are for V8 trucks).
  • 1500HD, 2500, 2500HD, 3500 and 3500HD models.
  • The redesigned 2007 truck. Only the 2007 “Classic,” which kept the older body, is listed.

The Gleyi listing also excludes the Avalanche, Tahoe, Suburban, Yukon and Escalade, and asks for extra verification on SS, Denali and Quadrasteer trucks.

A 4WD caution for the spindles: the spindle listing’s headline fitment is 2WD Silverado and Sierra 1500. Elsewhere on the same page it mentions 4WD, AWD and the GM SUVs, and says 4WD/AWD use needs the upper ball-joint stem trimmed. That’s a significant modification to a steering component. Treat these spindles as a 2WD part unless the seller confirms otherwise in writing.

Can you stack spindles and coils?

Some builds combine a drop spindle with a lowering coil for a bigger front drop, but none of these listings publish a combined figure. The Gleyi listing specifically warns against stacking lowering methods, such as drop spindles, aftermarket control arms or modified spring pockets, without confirming the total engineered drop. Before you pair parts from different brands, ask both sellers whether the combination is supported. Never cut springs to gain extra drop.

Shocks, bump stops and alignment

  • Shocks: the TOWGUARD listing says standard-length shocks may fit after a 2-inch drop but aren’t always ideal. It recommends lowered or shorter-stroke shocks for better rebound control. The sister-site build article warns that factory-length shocks can bottom out on a lowered truck.
  • Bump stops: the Gleyi listing notes that bump stops may need attention after lowering.
  • Alignment: all three listings call for an alignment after installation, and the Gleyi listing calls it mandatory. Lowering changes camber, caster and toe.
  • While it’s apart: the spindle listing suggests inspecting tie rods, wheel bearings, ball joints and brakes during the swap.

For the rest of the truck, from wheels and stance to keeping it livable as a daily, our sister site’s Street Truck Makeover for a Better Daily covers the planning side.

Front coil springs are stored under high load. Compressing and removing them safely takes the right tools and experience. If that isn’t you, have a suspension shop do the install.

Prostreetonline.com
Logo
Compare items
  • Total (0)
Compare
0
Shopping cart