Sale!

43.3-Inch Adjustable Aluminum GT Wing Spoiler: Universal Trunk-Mount Design

Give a compatible coupe or sedan a more aggressive track-inspired profile with this 43.3-inch universal aluminum GT wing. Its twin-pedestal mounting system uses approximately 19-inch bracket spacing, while adjustable wing angles allow the appearance and airfoil position to be tuned for the vehicle.

Because this is a universal spoiler, installation requires careful measurement, drilling and appropriate trunk reinforcement. Compatibility cannot be determined by trunk width alone.

Product Overview

Specification Details
Product type Universal rear GT wing
Wing span 43.3 inches / 110 cm
Pedestal spacing Approximately 19 inches / 48 cm
Material Aluminum alloy
Wing angle Adjustable
Mounting style Twin trunk-mounted pedestals
Vehicle type Compatible coupes and sedans with trunk lids
Installation Drilling and reinforcement normally required
Hardware Verify package contents
Professional installation Recommended
Aerodynamic results Vehicle- and installation-dependent

Track-Inspired Styling for Compatible Cars

The raised GT-wing design creates a more aggressive rear profile than a low factory-style lip spoiler. It is intended for owners building:

  • JDM-inspired street cars
  • Track-themed coupes
  • Sport compact sedans
  • Show cars
  • Drift-style builds
  • Autocross-inspired projects
  • Custom exterior packages

Its 43.3-inch width is compact enough for many smaller vehicles while remaining visually prominent.

Before ordering, compare the wing dimensions with the trunk, quarter panels, rear glass and overall vehicle width. “Universal” means adaptable—it does not mean the wing has personally agreed to fit every car ever manufactured.

Original price was: $55.95.Current price is: $49.99.

Key Dimensions

Measurement Size
Overall wing length 43.3 inches
Metric wing length 110 cm
Distance between mounting brackets Approximately 19 inches
Metric bracket spacing Approximately 48 cm

The bracket-spacing measurement must be compared with the usable structure beneath the trunk lid, not merely its painted exterior surface.

Aluminum-Alloy Construction

The wing is manufactured from aluminum alloy to provide a balance of weight, rigidity and weather resistance.

Potential advantages include:

  • Lower weight than comparable steel designs
  • Resistance to conventional iron rust
  • Rigid wing profile
  • Adjustable mounting hardware
  • Track-inspired appearance
  • Suitability for painted or wrapped finishes

Aluminum can still oxidize, corrode or suffer finish damage. Road salt, dissimilar-metal contact, loose hardware and trapped moisture should be addressed during installation and maintenance.

The supplied description does not identify the specific aluminum grade, wall thickness, tested load or maximum-speed rating.

Adjustable Wing Angle

The side plates or mounting arrangement permit the wing angle to be adjusted.

Changing the angle may affect:

  • Visual stance
  • Airflow separation
  • Aerodynamic drag
  • Rear-axle load
  • Wind noise
  • Trunk-lid stress
  • High-speed balance

A steeper angle does not automatically produce useful downforce. It may simply increase drag or turbulence.

For a street-driven vehicle, begin with the manufacturer’s neutral or recommended setting. Make small, equal adjustments on both sides and verify that all hardware remains secure.

Aerodynamic Claims: What This Wing Can and Cannot Guarantee

A properly engineered rear wing can create aerodynamic load when it operates in suitable airflow at sufficient speed. Whether this universal wing does so effectively depends on:

  • Vehicle shape
  • Roofline
  • Rear-window angle
  • Wing height
  • Wing angle
  • Airfoil profile
  • Mounting location
  • Vehicle speed
  • Underbody airflow
  • Front aerodynamic balance

This product should not be advertised as automatically:

  • Reducing drag
  • Improving fuel economy
  • Increasing traction
  • Making every vehicle more stable
  • Producing a specific amount of downforce
  • Improving lap times

Rear wings commonly increase drag when configured to create downforce. An incorrectly positioned wing can operate in turbulent air or make high-speed balance worse.

No wind-tunnel data, computational-fluid-dynamics analysis or vehicle-specific test results are supplied.

Universal Fitment Requirements

This wing may fit some vehicles with a separate rear trunk lid. Confirm all of the following before purchase:

  • Trunk-lid width
  • Usable flat mounting area
  • 19-inch pedestal spacing
  • Clearance beneath the mounting points
  • Access for nuts and backing plates
  • Trunk opening clearance
  • Rear-window clearance
  • Antenna clearance
  • Third-brake-light visibility
  • Rear-camera visibility
  • Factory spoiler-hole interference
  • Trunk hinge and torsion-bar operation
  • Sheet-metal strength
  • Vehicle width and legal requirements

Read the Aftermarket Spoiler Fitment Guide before treating universal dimensions as confirmed compatibility.

Vehicles That May Require Additional Work

Extra fabrication or reinforcement may be necessary on:

  • Hatchbacks
  • Liftbacks
  • SUVs
  • Trucks
  • Convertibles
  • Composite trunk lids
  • Carbon-fiber trunk lids
  • Double-skin trunk structures
  • Vehicles with factory spoilers
  • Vehicles with powered trunk mechanisms
  • Cars with rear antennas or cameras
  • Trunk lids with limited interior access

Do not install the wing on glass, plastic trim or an unsupported cosmetic panel.

Trunk Reinforcement Is Important

A raised wing creates leverage at its mounting points. Airflow, vibration and trunk movement transfer that load into the sheet metal.

Small washers alone may not distribute the load adequately.

A safe installation may require:

  • Large backing plates
  • Reinforcement brackets
  • Properly graded fasteners
  • Locking nuts
  • Rubber or isolating gaskets
  • Corrosion protection
  • Seam sealer
  • Vehicle-specific fabrication

Without reinforcement, the trunk lid may:

  • Flex
  • Crack
  • Distort
  • Tear around the holes
  • Develop paint damage
  • Leak water
  • Lose alignment

Professional installation is strongly recommended when the underside of the mounting area is inaccessible or structurally unclear.

Tools and Materials You May Need

  • Measuring tape
  • Masking tape
  • Straightedge
  • Center punch
  • Drill
  • Correct drill bits
  • Deburring tool
  • Rust-preventive primer
  • Automotive seam sealer
  • Touch-up paint
  • Backing plates
  • Rated mounting hardware
  • Torque wrench
  • Trim-removal tools
  • Vacuum
  • Eye protection
  • Cut-resistant gloves
  • Second installer

Verify what comes with the wing before beginning. Universal kits do not always include hardware suitable for every trunk structure.

How to Install a Universal GT Wing

1. Inspect the Wing

Check for:

  • Shipping damage
  • Bent brackets
  • Missing hardware
  • Damaged threads
  • Uneven side plates
  • Finish defects
  • Loose components

Assemble the wing loosely on a workbench before placing it on the vehicle.

2. Measure the Trunk Lid

Confirm that the 43.3-inch wing and approximately 19-inch bracket spacing fit the available area.

Inspect both sides of the trunk lid. The mounting location must provide clearance for backing plates and fasteners.

3. Protect the Paint

Apply masking tape over the proposed mounting area. This protects the finish during layout and provides a surface for marking.

4. Center the Wing

Use the trunk edges, rear glass and centerline to position the wing symmetrically.

Measure from multiple fixed points. Do not center it solely by eye.

5. Check Trunk Operation

With the wing temporarily positioned, open and close the trunk carefully.

Verify clearance from:

  • Rear glass
  • Roof
  • Antenna
  • Body panels
  • Existing spoiler
  • Trunk hinges
  • Garage ceiling

6. Inspect Beneath the Drill Points

Before drilling, confirm that the selected locations do not contact:

  • Wiring
  • Trunk hinges
  • Torsion bars
  • Release cables
  • Factory reinforcement ribs
  • Double-wall areas without access
  • Electronic modules
  • Backup-camera wiring

7. Create a Template

Use the pedestal bases or a paper template to mark hole locations accurately. Confirm the template against the actual hardware.

8. Drill Pilot Holes

Wear eye protection. Start with small pilot holes and enlarge them gradually to the required diameter.

Use a drill stop when hidden clearance is limited.

9. Deburr and Protect the Metal

Remove sharp edges and metal shavings. Treat bare steel with:

  • Corrosion-resistant primer
  • Touch-up paint
  • Appropriate seam protection

Do not leave raw drilled edges exposed.

10. Install Sealing Gaskets

Use suitable gaskets or sealant around the mounting holes to help prevent water intrusion.

Do not use excessive sealant that blocks drainage or makes later inspection impossible.

11. Add Backing Plates

Position appropriately sized backing plates beneath the trunk lid. They should distribute load beyond the immediate bolt holes.

12. Mount the Pedestals

Install the pedestals evenly without fully tightening one side first.

Confirm that both bases sit flat without forcing the trunk sheet metal to conform to an incompatible shape.

13. Install and Level the Wing

Attach the airfoil to both pedestals. Measure its height and angle on each side.

The settings should match unless the manufacturer provides a different configuration.

14. Tighten the Hardware

Tighten fasteners evenly according to the hardware manufacturer’s specification.

Do not overtighten and crush the trunk lid, pedestal or aluminum components.

15. Test for Leaks

Use a controlled low-pressure water test and inspect the trunk interior.

Correct leaks before reinstalling trim.

16. Road-Test Conservatively

Begin at low speed and listen for:

  • Vibration
  • Rattling
  • Whistling
  • Trunk movement
  • Contact with body panels

Stop immediately if the wing moves or the trunk structure flexes.

Balancing Front and Rear Aerodynamics

Adding rear aerodynamic load without considering the front of the vehicle can change handling balance.

A functional aero package may also require evaluation of:

  • Front splitter
  • Air dam
  • Undertray
  • Ride height
  • Suspension setup
  • Tire grip
  • Alignment
  • Vehicle speed
  • Track conditions

Our Front Splitter Installation Guide explains why real aerodynamic hardware needs structural support rather than attachment to a flexible bumper cover.

Do not add front aero solely to “balance” an untested rear wing. Vehicle-specific testing is required to understand actual aerodynamic behavior.

Common Installation Mistakes

Measuring Only the Trunk Exterior

The underside must provide space for hardware and reinforcement.

Mounting Through a Single Sheet Without Backing Plates

Concentrated loads can distort or tear thin trunk metal.

Installing the Wing Crooked

Small measurement errors become obvious across a 43.3-inch span.

Drilling Before Checking Trunk Operation

The wing may contact the rear glass, roof or body when the trunk opens.

Ignoring the Third Brake Light

The wing must not block required lighting from normal viewing angles.

Using Household Silicone

Use automotive-compatible sealing materials that will not damage paint or trap moisture.

Setting Maximum Angle Immediately

A steep angle can increase drag, noise and mounting load without delivering useful performance.

Claiming Fuel-Economy Gains

A raised GT wing usually adds frontal area and can increase aerodynamic drag. Any fuel-economy change requires controlled testing.

Driving at High Speed Immediately

Inspect the mounting system after low-speed testing and several normal trips before exposing it to greater aerodynamic load.

Inspection and Maintenance

Check the wing regularly for:

  • Loose fasteners
  • Cracked brackets
  • Trunk-lid deformation
  • Water intrusion
  • Corrosion
  • Finish damage
  • Uneven wing angle
  • Backing-plate movement
  • Paint cracking
  • Increased vibration
  • Contact with body panels

Inspect it after:

  • Installation
  • First drive
  • First highway trip
  • Heavy rain
  • Automatic car washes
  • Track use
  • Any impact
  • Trunk adjustment

Remove the wing from service if its mounts, brackets or trunk structure show damage.

Cleaning the Aluminum Wing

Use:

  • Automotive shampoo
  • Soft wash mitt
  • Microfiber towels
  • Aluminum-safe detailing products

Avoid:

  • Abrasive metal polish unless the finish permits it
  • Harsh acids
  • Caustic wheel cleaner
  • Pressure washing directly at mounting seals
  • Automatic brushes that can catch the wing
  • Leaning or pulling on the airfoil

A GT wing is not a trunk handle. Using it as one is an efficient way to test which component gives up first.

Who Should Buy This Wing?

This universal spoiler may suit:

  • Coupe and sedan owners
  • JDM-inspired builds
  • Show cars
  • Drift-style projects
  • Track-themed street cars
  • Custom exterior projects
  • Fabricators comfortable with universal hardware
  • Buyers prepared to reinforce the trunk

It may not suit:

  • Buyers wanting no-drill installation
  • Vehicles without a separate trunk lid
  • Composite panels without engineered reinforcement
  • Cars with limited internal mounting access
  • Drivers expecting guaranteed downforce
  • Vehicles where the wing blocks lighting or visibility
  • Owners unwilling to measure before ordering

Frequently Asked Questions

How wide is the wing?

The wing measures approximately 43.3 inches, or 110 cm.

What is the spacing between the brackets?

The mounting brackets are approximately 19 inches, or 48 cm, apart.

Is it truly universal?

It is a universal-style product, but fitment requires sufficient trunk width, mounting access, reinforcement and clearance.

Does installation require drilling?

Most installations will require drilling the trunk lid. No-drill compatibility is not stated.

Is mounting hardware included?

The supplied information does not provide a complete hardware inventory. Verify the package contents before installation.

Is the wing angle adjustable?

Yes. Its mounting design permits angle adjustment.

Does it improve fuel economy?

No fuel-economy improvement can be guaranteed. A rear wing may increase aerodynamic drag.

Does it create downforce?

It may generate aerodynamic load under appropriate conditions, but no vehicle-specific test data or downforce figures are supplied.

Will it make the car more stable?

Not necessarily. Stability depends on vehicle shape, mounting location, speed, angle and overall aerodynamic balance.

Is the wing made from aluminum?

Yes. The product is described as aluminum alloy.

Will aluminum rust?

Aluminum does not produce iron rust, but it can oxidize or corrode, especially around dissimilar metals and damaged finishes.

Does the trunk need reinforcement?

Reinforcement is strongly recommended when the mounting surface is thin or unsupported.

Can it fit a hatchback?

A hatchback would generally require custom mounting and reinforcement. Standard trunk-mount compatibility should not be assumed.

Should it be professionally installed?

Yes, particularly when drilling, reinforcement or access through double-layer trunk construction is involved.

Final Thoughts

The 43.3-inch adjustable aluminum GT wing provides an aggressive rear profile for compatible coupes and sedans. Its 19-inch pedestal spacing and adjustable airfoil offer flexibility, but successful installation depends on far more than whether the wing fits between the quarter panels.

Measure both sides of the trunk, reinforce the mounting points, seal every drilled hole and treat aerodynamic claims honestly. It can absolutely make a car look faster. Whether it makes the car behave better at speed is a question for proper engineering—not the product-title department.

Specification: 43.3-Inch Adjustable Aluminum GT Wing Spoiler: Universal Trunk-Mount Design

Brand

User Reviews

0.0 out of 5
★★★★★
0
★★★★★
0
★★★★★
0
★★★★★
0
★★★★★
0
Write a review

There are no reviews yet.

Be the first to review “43.3-Inch Adjustable Aluminum GT Wing Spoiler: Universal Trunk-Mount Design”

Prostreetonline.com
Logo
Compare items
  • Total (0)
Compare
0
Shopping cart