Vehicle Fitment
✅ Fits:
-
2006 Toyota RAV4
-
2007 Toyota RAV4
-
2008 Toyota RAV4
-
2009 Toyota RAV4
-
2010 Toyota RAV4
-
2011 Toyota RAV4
-
2012 Toyota RAV4
-
Front position
-
FWD and AWD models
⚠️ Always confirm:
-
4-cylinder vs V6
-
Sport vs Base trim
-
Stock ride height configuration
What’s Included in Quick-Strut 173013
-
New Monroe strut
-
Pre-installed coil spring
-
Upper strut mount
-
Bearing plate
-
Dust boot and bump stop
No spring compressor required. Bolt in and go.
Translation: safer install, less labor time.
Key Features
-
Nitrogen gas-charged twin-tube design
-
OE-calibrated damping
-
Factory-matched spring rate
-
Corrosion-resistant finish
-
Designed to restore original ride height
Built to meet OE ride and handling expectations.
Performance Benefits
-
Eliminates front-end clunking
-
Reduces body roll
-
Improves steering stability
-
Reduces nose dive
-
Restores smooth highway ride
Perfect for high-mileage RAV4s needing full suspension refresh.
ASSEMBLED IN THE USA – This Quick-Strut assembly is assembled with pride in Paragould, Arkansas from domestic and imported components
Installation Notes
-
Replace both front struts together
-
Perform wheel alignment after installation
-
Inspect sway bar links and bushings
-
Torque all hardware to spec
Because fresh suspension deserves proper alignment.
MONROE QUICK-STRUT ASSEMBLIES
The first and only Quick-Strut. Monroe Quick-Strut assemblies are unmatched in quality, durability and fit. They simplify the installation process, including everything needed for strut replacement in a single, fully assembled unit with no need for a spring compressor.
Quick-Strut units feature high-quality steel, application-specific coil springs to restore ride height and strut rods which surpass the OE flexibility standard, maintaining structural integrity in the event of a major road impact.
Restore your car, light truck, SUV or CUV back to OE-quality ride performance and drivability with a Monroe Quick-Strut assembly. Including all the components required for strut replacement without the need for a spring compressor, this complete strut assembly features the strut, coil spring and strut mount preassembled for easy installation. Strut assemblies perform two main jobs: perform a damping function like shock absorbers and provide structural support for the vehicle suspension by supporting the spring and holding the tire in an aligned position.
CAUSES & CONSEQUENCES OF STRUT FAILURE
Like many parts on your vehicle, struts are subject to wear. The rate of wear depends on a wide range of variables, such as road and environmental conditions, your driving style and vehicle load. Causes of worn struts include damaged bushings, exposure to the elements, loss of oil viscosity and gradual degradation of internal components over time. Driving with worn struts can result in problems ranging from reduced braking efficiency, cause premature tire wear, loss of stability and damage to other suspension parts.
IMPORTANCE OF AN ALIGNMENT
Always perform an alignment anytime replacement shocks, struts or other ride control parts are installed. Camber, toe and caster settings can all be affected by installing new struts. Failure to make sure the vehicle’s alignment is within factory specifications can lead to problems like premature tire wear.
IMPORTANCE OF MAINTAINING RIDE HEIGHT
Proper ride height is crucial to vehicle durability, performance and safety. When inspecting a vehicle, don’t just check the static ride height. The dynamic ride height – the ride height of a vehicle in motion – may tell a different story. The cause of dynamic ride height issues is often worn or damaged coil springs. Don’t just replace the strut – be sure to also inspect for and replace worn coil springs.
HOW TO PROPERLY INSTALL A STRUT ASSEMBLY
Avoid noise after installing a strut assembly with this four-step procedure.
- Loosely install 1 or 2 upper mounting nuts and position lower strut mount to steering knuckle assembly
- Install lower mounting bolts and lower vehicle to the ground
- Locate manufacturer torque specifications
- Torque lower bolts and secure upper mounting nuts in alternating pattern
Final Verdict
The Monroe Quick-Strut 173013 for 2006–2012 Toyota RAV4 is a complete OE-style solution for restoring ride comfort, control, and factory ride height. Pre-assembled design simplifies installation and ensures balanced suspension performance.
Because dependable SUVs should drive like it.
Patrick –
The part works as it should. Will update after driving on it for awhile.
dfw_area –
So far seems like a quality product. All good. Would recommend.
Solitario –
Tremendo amortiguadorSe ve la calidad
Q Sanchez –
Lo he recibido en buen estado y en el tiempo prometido
Charl8 –
Used these for replacements, & will again when needed. I live on a bad road.
Jim –
Yes, yes, yes, these are what you’re looking for. Smooth and powerful
navarro808 –
These struts failed after 3 months of use and are worse that the old struts that I replaced.
Zoe –
My bad should have gone for KYB or better, now riding my 2017 RAV4, can feel slightest bump and uneven road makes a rocky ride even on the freeway!!!