Kenwood Mono Amps for a Subwoofer: Rated Power at 4 and 2 Ohms, and How to Wire for It

Kenwood mono amps are often shopped by the big number on the box: 1000W, 2000W. That figure is a maximum, not what the amp delivers continuously. What matters for a subwoofer is the rated (RMS) power at the impedance your sub wiring actually presents to the amp. Here’s what Kenwood’s own spec sheets say about five Kenwood mono amp models in our store, and how to wire a sub to get the rated output without going below the amp’s minimum load.

Already installed and the system shuts off when you turn it up? Our sister site walks through that in Car Stereo Cuts Out at High Volume? Diagnose It Before Buying Parts.

Max power and rated power aren’t the same number

Kenwood lists a “max power” figure and separate RMS ratings at 4 ohms and 2 ohms. The RMS ratings are measured under stated conditions (a frequency range and a distortion limit), so they’re the numbers to compare across amps and to match against your subwoofer’s RMS rating. Max power doesn’t tell you much when you’re sizing a system.

Five Kenwood mono amps by rated power

AmpRMS at 4 ohmsRMS at 2 ohmsMax power (Kenwood)Lowest load Kenwood lists
Kenwood KAC-531300W500W1000W2 ohms (2–8 ohms allowable)
Kenwood KAC-D5101300W500W1000W2 ohms (2–8 ohms allowable)
Kenwood eXcelon X503-1300W500W1000W2 ohms (2–8 ohms allowable)
Kenwood eXcelon XR601-1400W600WNot listed (500W max dynamic power at 4 ohms)Rated at 2 ohms; minimum not stated on the spec page
Kenwood KAC-9106D500W1000W2000W2 ohms (2–8 ohms allowable)

The KAC-531, KAC-D5101 and X503-1 share the same 300W/500W ratings on paper. They differ in features. For example, Kenwood lists a wired remote level control with the X503-1, and the KAC-531’s spec listing includes one too, while Kenwood’s KAC-D5101 page doesn’t list one. If a remote bass level control matters to you, check each model’s included accessories.

No 1-ohm rating on these Kenwood mono amps

None of the spec sheets we checked for these five amps lists a 1-ohm rating. Four of them state an allowable range of 2 to 8 ohms. That matters, because some subwoofer wiring choices end up at 1 ohm, and running an amp below its listed load can trigger its protection circuit. Plan your wiring for a final load of 2 or 4 ohms.

Getting a 2-ohm or 4-ohm load from your sub

The load the amp sees depends on the sub’s voice coils and how you wire them. Coils wired in series add their impedance. Identical coils wired in parallel divide it by the number of coils.

Subwoofer setupWiringFinal nominal loadSuits these Kenwood amps?
One single 4-ohm coil subDirect4 ohmsYes, at the 4-ohm rating
One single 2-ohm coil subDirect2 ohmsYes, at the 2-ohm rating
One dual 4-ohm coil subCoils in parallel2 ohmsYes, at the 2-ohm rating
One dual 2-ohm coil subCoils in series4 ohmsYes, at the 4-ohm rating
One dual 2-ohm coil subCoils in parallel1 ohmNo, below the listed minimum
Two dual 4-ohm coil subsEach sub’s coils in series (8 ohms), subs in parallel4 ohmsYes, at the 4-ohm rating
Two dual 2-ohm coil subsEach sub’s coils in series (4 ohms), subs in parallel2 ohmsYes, at the 2-ohm rating

These are nominal impedances. A multimeter reads DC resistance, which is lower than the nominal rating, so a “4-ohm” coil reading a little under 4 ohms on a meter is normal. Count every coil and trace every connection before you power up. The cut-out troubleshooting article above makes the same point: the number printed on one coil isn’t necessarily the load the amp sees.

Matching power to the sub

Once you know the final load, compare the amp’s RMS rating at that load with your subwoofer’s RMS power rating. A rough match is the goal. A big mismatch either way can make it easier to push the system into distortion when chasing volume. Set the gain to match the head unit’s output rather than using it as a volume knob, and use wiring and fusing sized for the amp. Kenwood lists two 30A fuses on the X503-1 and KAC-D5101, for example.

If the new amp powers on but you hear nothing, check the remote turn-on lead and input wiring first. Our sister site covers that in Aftermarket Radio Turns On but No Sound?

Prostreetonline.com
Logo
Compare items
  • Total (0)
Compare
0
Shopping cart